View AD1939YSTZRL_6562285.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

4 adc/8 dac with pll, 192 khz, 24 - bit codec ad1939 rev. c information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is g ranted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062 - 9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ? 2006 C 2010 analog devices, inc. all rights reserved. features pll generated or direct master clock low emi design 1 12 db dac/10 7 db adc dynamic range and snr ?94 db thd + n single 3.3 v supply tolerance for 5 v logic inputs supports 24 - bits and 8 khz to 192 khz sample rates differential adc input differentia l dac output log volume control with autoramp function spi controllable for flexibility software - controllable clickless mute software power - down right - justified, left - justified, i 2 s, and tdm modes master and slave modes up to 16 - channel in put /output 64 -l ead lqfp package qualified for automotive applications applications automotive audio systems home theater systems set - top boxes digital audio effects processors general description the ad1939 is a high performance, single - chip codec that provides four ana log - to - digital converters (adcs) with differential input , and eight digital - to - analog converters (dacs) with differential output using the analog devices, inc. patented multibit sigma - delta ( - ) architecture. an spi port is included, allowing a microcontr oller to adjust volume and many other parameters. the ad1939 operates from 3.3 v digital and analog supplies. the ad1939 is available in a 64 - lead (differential output) lqfp package. the ad1939 is designed for low emi. this consideration is apparent in bot h the system and circuit design architectures. by using the on - board pll to derive the master clock from the lr clock or from an external crystal, the ad1939 eliminates the need for a separate high frequency master clock and can also be used with a suppr essed bit clock. the dacs and adcs are designed using the latest analog devices continuous time architectures to further minimize emi. by using 3.3 v supplies, power consumption is minimized, further reducing emissions. functional block dia gram digital filter serial data port digital audio input/output precision voltage reference timing management and control (clock and pll) spi control port control data input/output ad1939 adc adc adc adc analog audio inputs analog audio outputs dac dac dac dac dac dac dac dac digital filter and volume control sdata out sdata in clocks 06071-001 figure 1.
ad1939 rev. c | page 2 of 32 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 general description ......................................................................... 1 functional block diagram .............................................................. 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 test conditions ............................................................................. 3 analog performance specifications ........................................... 3 crystal oscillator specifications ................................................. 4 digital input/output specifications ........................................... 5 power supply specifications ........................................................ 5 digital filters ................................................................................. 6 timing specifications .................................................................. 6 absolute maximum ratings ............................................................ 8 thermal resistance ...................................................................... 8 esd caution .................................................................................. 8 pin configuration and function descriptions ............................. 9 typical performance characteristics ........................................... 11 theory of operation ...................................................................... 13 analog - to - digital converters (adcs) .................................... 13 digital - to - analog converters (dacs) .................................... 13 clock signals ............................................................................... 13 reset and power - down ............................................................. 14 serial control port ..................................................................... 14 power supply and voltage reference ....................................... 15 serial data ports data format ............................................... 15 time - division multiplexed (tdm) modes ............................ 15 daisy - chain mode ..................................................................... 19 control registers ............................................................................ 24 definitions ................................................................................... 24 pll and clock control registers ............................................. 24 dac control registers .............................................................. 25 adc control registers .............................................................. 27 additional modes ....................................................................... 29 application circuits ....................................................................... 30 outline dimensions ....................................................................... 31 ordering guide .......................................................................... 31 automotive products ................................................................. 31 revision history 9/10 rev . b to rev. c added qualified for automotive applications to the features section ................................................................................................ 1 changed case temperature from 130c to 125c ...................... 4 change d t a from ?40c to +130c to ?40c to +105c ........... 5 changed t a from ?40c to +130c to ?40c to +105c ........... 7 changes to ordering guide .......................................................... 31 added automotive products section ........................................... 31 3/10 rev . a to rev. b changes to ordering guide .......................................................... 31 6 /0 7 rev . 0 to rev. a deleted i 2 c referen ces ....................................................... universal change to figure 1 ........................................................................... 1 changes to figure 2 ........................................................................... 9 changes to table 10 .......................................................................... 9 changes to table 11 ....................................................................... 14 changes to table 12 ....................................................................... 16 changes to figure 24 and figure 25 ............................................ 22 changes to table 13 ....................................................................... 23 change to figure 26 ....................................................................... 23 changes to table 15 and table 16 ................................................ 24 changes to figure 27 and figure 28 ............................................ 29 change to figure 30 ....................................................................... 30 updated outline dimensions ....................................................... 31 changes to ordering guide .......................................................... 31 7 /06 revision 0: initial version
ad1939 rev. c | page 3 of 32 specifications test conditions performance of all channels is identical, exclusive of the interchannel gain mis match and interchannel phase deviation specifications. supply voltages (avdd, dvdd) 3.3 v temperature range 1 a s specified in table 1 and table 2 master clock 12.288 mhz (48 khz f s , 256 f s mode ) input sample rate 48 khz measurement bandwidth 20 hz to 20 khz word width 24 bits load capacitance (digital output) 20 pf load current (digital output) 1 ma or 1.5 k? to ? dvdd supply input voltage high 2.0 v input voltage low 0.8 v 1 functionally guaranteed at ?40c to +125c case temperature . analog performance s pecifications specifications guaranteed at an ambient temperature of 25c. table 1 . parameter conditions /comments min typ max unit analo g- to - digital converters adc resolution all adcs 24 bits dynamic range 20 hz to 20 khz, ?60 db input no filter (rms) 96 102 db with a - weighted filter (rms) 98 105 db total harmonic distortion + noise ?1 dbfs ?96 ?87 db full - scale inpu t voltage (differential) 1.9 v rms gain error ?10 +10 % interchannel gain mismatch ?0.25 +0.25 db offset error ?10 0 +10 mv gain drift 100 ppm/c interchannel isolation ?110 db cmrr 100 mv rms, 1 khz 55 db 100 mv rms, 20 khz 55 db input resistance 14 k? input capacitance 10 pf input common - mode bias voltage 1.5 v digital - to - analog converters dynamic range 20 hz to 20 khz, ?60 db input no filter (rms) 102 107 db with a - weighted filter (rms) 105 110 db with a - weighted filter (av era ge) 112 db total harmonic distortion + noise 0 dbfs two channels running ?94 db eight channels running ?86 ?76 db full - scale output voltage 1.76 (4.96) v rms (v p -p) gain error ?10 +10 % interchannel gai n mismatch ?0.2 +0.2 db offset error ?25 ?6 +25 mv gain drift ?30 +30 ppm/c interchannel isolation 100 db
ad1939 rev. c | page 4 of 32 parameter conditions /comments min typ max unit interchannel phase deviation 0 degrees volume control step 0.375 db volume control range 95 db de - emphasis gain error 0.6 db output resistance at each pin 100 ? reference internal reference voltage filtr pin 1.50 v external reference voltage filtr pin 1.32 1.50 1.68 v common - mode reference output cm pin 1.50 v regulator input supply voltage vsupply p in 4.5 5 5.5 v regulated output voltage vsense pin 3.19 3.37 3.55 v specifications measured at a case temperature of 125 c. table 2. parameter conditions /comments min typ max unit analog - to - digital converters adc resoluti on all adcs 24 bits dynamic range 20 hz to 20 khz, ?60 db input no filter (rms) 93 102 db with a - weighted filter (rms) 96 104 db total harmonic distortion + noise ?1 dbfs ?96 ?87 db full - scale input voltage (differential) 1.9 v rms gain error ?10 +10 % interchannel gain mismatc h ?0.25 +0.25 db offset error ?10 0 +10 mv digital - to - analog converters dynamic range 20 hz to 20 khz, ?60 db input no filter (rms) 101 107 db with a - weighted filter (rms) 104 110 db with a - weighted filter (average) 112 db total harmonic distortion + noise 0 dbfs two channels running ?94 db eight channels running ?86 ?70 db full - scale output voltage 1.76 (4.96) v rms (v p -p) gain error ?10 +10 % interchannel gain mismatch ?0.2 +0.2 db offset error ?25 ?6 +25 mv gain drift ?30 +30 ppm/c reference internal reference voltage filtr pin 1.50 v external reference voltage filtr pin 1.32 1.50 1.68 v common - mode reference output cm pin 1.50 v regulator input supply voltage vsupply pin 4.5 5 5. 5 v regulated output voltage vsense pin 3.2 3.43 3.65 v crystal oscillator s pecifications table 3 . parameter min typ max unit transconductance 3.5 mmhos
ad1939 rev. c | page 5 of 32 digital input/output specifications ?40c < t a < +1 05 c, dvdd = 3.3 v 10%. table 4. parameter conditions/comments min typ max unit high level input voltage (v ih ) 2.0 v mclki/xi pin 2.2 v low level input voltage (v il ) 0.8 v input leakage i ih @ v ih = 2.4 v 10 a i il @ v il = 0.8 v 10 a high level output voltage (v oh ) i oh = 1 ma dvdd ? 0.60 v low level output voltage (v ol ) i ol = 1 ma 0.4 v input capacitance 5 pf power supply specifi cations table 5 . parameter conditions/comments min typ max unit supplies voltage dvdd 3.0 3.3 3.6 v a vdd 3.0 3.3 3.6 v vsupply 4.5 5.0 5.5 v digital current m aster clock = 256 f s normal operation f s = 48 khz 56 ma f s = 96 khz 65 ma f s = 192 khz 95 ma power - down f s = 48 khz to 192 khz 2.0 ma analog current normal operation 74 ma power - down 23 ma dissipation operation m aster clock = 256 f s , 48 khz all supplies 429 mw digital supply 185 mw analog supply 244 mw power - down, all supplies 83 mw power supply rejection ratio signal at analog supply pins 1 khz , 200 mv p -p 50 db 20 khz , 200 mv p -p 50 db
ad1939 rev. c | page 6 of 32 digital filters table 6 . parameter mode factor min typ max unit adc decimation filter all modes, typ ical @ 48 khz pass band 0.4375 f s 21 khz pass - band ripple 0.015 db transition band 0.5 f s 24 khz stop band 0.5625 f s 27 khz stop - band attenuation 79 db group delay 22.9844/ f s 479 s dac interpolation filter pass band 48 khz mode, typ ical @ 48 khz 0.4535 f s 22 khz 96 khz mode, ty p ical @ 96 khz 0.3646 f s 35 khz 192 khz mode, typ ical @ 192 khz 0.3646 f s 70 khz pass - band ripple 48 khz mode, typ ical @ 48 khz 0.01 db 96 khz mode, typ ical @ 96 khz 0.05 db 192 khz mode, typ ical @ 192 khz 0.1 db transition band 48 khz mode, typ ical @ 48 khz 0.5 f s 24 khz 96 khz mode, typ ical @ 96 khz 0.5 f s 48 khz 192 khz mode, typ ical @ 192 khz 0.5 f s 96 khz stop band 48 khz mode, typ ical @ 48 khz 0.5465 f s 26 khz 96 khz mode, typ ical @ 96 khz 0.6354 f s 61 khz 19 2 khz mode, typ ical @ 192 khz 0.6354 f s 122 khz stop - band attenuation 48 khz mode, typ ical @ 48 khz 70 db 96 khz mode, typ ical @ 96 khz 70 db 192 khz mode, typ ical @ 192 khz 70 db group delay 48 khz mode, typ ical @ 48 khz 25/f s 521 s 96 khz mode, typ ical @ 96 khz 11/f s 115 s 192 khz mode, typ ical @ 192 khz 8/f s 42 s timing specification s ?40c < t a < +1 05 c, dvdd = 3.3 v 10%. table 7 . parameter condition comments min max unit input master clock (mclk) and reset t mh mclk duty cycle dac/adc clock source = pll clock @ 256 f s , 384 f s , 512 f s , and 768 f s 40 60 % t mh dac/adc clock source = direct mclk @ 512 f s (bypass on - chip pll) 40 60 % f mclk mclk frequency pll mode, 256 f s reference 6.9 13.8 mhz f mclk direct 512 f s mode 27.6 mhz t pdr l ow 15 ns t pdrr r ecovery reset to active output 4096 t mclk pll lock t ime mclk and lrclk input 10 ms 256 f s vco clock , output duty cycle , mclko/xo p in 40 60 %
ad1939 rev. c | page 7 of 32 parameter condition comments min max unit spi port see figure 11 t cch cclk high 35 ns t ccl cclk low 35 ns f cclk cclk frequency f cclk = 1/t ccp ; only t c cp shown in figure 11 10 mhz t cds cin setup to cclk rising 10 ns t cdh c in hold from cclk rising 10 ns t cls clatch setup to cclk rising 10 ns t clh clatch hold from cclk falling 10 ns t clhigh clatch high not shown in figure 11 10 ns t coe cout enable from cclk falling 30 ns t cod cout delay from cclk falling 30 ns t coh cout hold from cclk falling, not shown in figure 11 30 ns t cots cout tri state from cclk falling 30 ns dac serial port see figure 24 t dbh dbclk high slave mode 10 ns t dbl dbclk low slave mode 10 ns t dls dlrclk setup to dbclk rising, slave mode 10 ns t dlh dlrclk hold from dbclk rising, slave mode 5 ns t dls dlrclk skew from dbclk falling, master mode ?8 +8 ns t dds dsdata setup to dbclk rising 10 ns t ddh dsdata hold from dbclk rising 5 ns adc serial port see figure 25 t abh abclk high slave mode 10 ns t abl abclk low slave mode 10 ns t als alrclk setup to abclk risin g, slave mode 10 ns t alh alrclk hold from abclk rising, slave mode 5 ns t als alrclk skew from abclk falling, master mode ?8 +8 ns t abdd asdata delay from abclk falling 18 ns auxiliary interface t axds aauxdata setup to auxbclk rising 10 ns t a xdh aauxdata hold from auxbclk rising 5 ns t dxdd dauxdata delay from auxbclk falling 18 ns t xbh auxbclk high 10 ns t xbl auxbclk low 10 ns t dls auxlrclk setup to auxbclk rising 10 ns t dlh auxlrclk hold from auxbclk rising 5 ns
ad1939 rev. c | page 8 of 32 absolute maximu m ratings table 8 . parameter rating analog (avdd) ?0.3 v to +3.6 v digital (dvdd) ?0.3 v to +3.6 v vsupply ?0.3 v to +6.0 v input current (except supply pins) 20 ma analog input voltage (signal pins) C 0.3 v to avdd + 0.3 v digital input voltage (signal pins) ?0.3 v to dvdd + 0.3 v operating tempera ture range (case) ?40c to +125c storage temperature range ?65c to +150c stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. thermal resistance ja represents thermal resist ance, junction -to - ambient; jc represents the thermal resistance, junction - to - case. all characteristics are for a 4 - layer board. table 9 . thermal resistance package type ja jc unit 64-l ead lqfp 47 11.1 c/w esd caution
ad1939 rev. c | page 9 of 32 pin configuration and function descripti ons nc 64 nc 63 avdd 62 lf 61 adc2rn 60 adc2rp 59 adc2ln 58 adc2lp 57 adc1rn 56 adc1rp 55 adc1ln 54 adc1lp 53 cm 52 avdd 51 nc 50 nc 49 dvdd 17 dsdata3 18 dsdata2 19 dsdata1 20 dbclk 21 dlrclk 22 vsupply 23 vsense 24 vdrive 25 asdata2 26 asdata1 27 abclk 28 alrclk 29 cin 30 cout 31 dvdd 32 agnd 1 mclki/xi 2 mclko/xo 3 agnd 4 avdd 5 ol3p 6 ol3n 7 or3p 8 or3n 9 ol4p 10 ol4n 11 or4p 12 or4n 13 pd/rst 14 dsdata4 15 dgnd 16 agnd 48 filtr 47 agnd 46 avdd 45 agnd 44 or2n 43 or2p 42 ol2n 41 ol2p 40 or1n 39 or1p 38 ol1p 36 clatch 35 cclk 34 dgnd 33 ol1n 37 ad1939 top view (not to scale) differential output nc = no connect 06071-021 figure 2 . 64 - lead lqfp, differential output , pin configuration table 10 . pin function descriptions pin no. in/out mnemonic description 1 i agnd analog grou nd. 2 i mclki/xi master clock input/crystal oscillator input. 3 o mclko/xo master clock output/crystal oscillator output. 4 i agnd analog ground. 5 i avdd analog power supply. connect to analog 3.3 v supply. 6 o ol3p dac 3 left positive output. 7 o o l3n dac 3 left negative output. 8 o or3p dac 3 right positive output. 9 o or3n dac 3 right negative output. 10 o ol4p dac 4 left positive output. 11 o ol4n dac 4 left negative output. 12 o or4p dac 4 right positive output. 13 o or4n dac 4 right negat ive output 14 i pd / rst power - down reset (active low). 15 i/o dsdata4 dac input 4 . in put to dac l4 and dac r4 /dac tdm data out 2/aux adc 1 data in . 16 i dgnd digital ground. 17 i dvdd digital power supply. connect to digital 3.3 v supply. 18 i/o dsdata3 dac input 3 . input to d ac l3 and dac r3 /dac tdm data in 2/ aux dac 2 d ata o ut . 19 i/o dsdata2 dac input 2 . input to dac l2 and dac r2 /dac tdm data out 1/aux adc 1 data in . 20 i dsdata1 dac input 1 . input to dac l1 and dac r1 /dac tdm data in 1/aux adc 2 data in . 21 i/o dbclk bit clock for dacs. 22 i/o dlrclk lr clock for dacs. 23 i vsupply 5 v input to regulator, emitter of pass transistor. 24 i vsense 3.3 v output of regulator, collector of pass transistor.
ad1939 rev. c | page 10 of 32 pin no. in/out mnemonic description 25 o v drive drive for base of pass transistor. 26 i/o asdata2 adc serial data output 2 (adc l2 and adc r2 )/adc tdm data input/ aux dac 1 data output. 27 o asdata1 adc serial data output 1 ( adc l1 and adc r1 )/adc tdm data ou tput. 28 i/o abclk bit clock for adc s. 29 i/o alrclk lr clock for adcs. 30 i cin control data input (spi). 31 i/o cout control data output (spi). 32 i dvdd digital power supply. connect to digital 3.3 v supply. 33 i dgnd digital ground. 34 i cclk control clock input (spi). 35 i clatch latch input for control data (spi). 36 o ol1p dac 1 left positive output. 37 o ol1n dac 1 left negative output. 38 o or1p dac 1 right positive output. 39 o or1n dac 1 right negative output. 40 o ol2p dac 2 left positive output. 41 o ol2n dac 2 left negative output. 42 o or2p dac 2 right positive output. 43 o or2n dac 2 right negative output . 44 i agnd analog ground. 45 i avdd analog power supply. connect to analog 3.3 v supply. 46 i agnd analog ground. 47 o f i ltr voltage reference filter capacitor connection. bypass with 10 f||100 nf to agnd. 48 i agnd analog ground. 49 nc no connect. 50 nc no connect. 51 i avdd analog power supply. connect to analog 3.3 v supply. 52 o cm common - mode reference filter capacitor connectio n. bypass with 47 f||100 nf to agnd. 53 i adc1lp adc1 left positive input. 54 i adc1ln adc1 left negative input. 55 i adc1rp adc1 right positive input. 56 i adc1rn adc1 right negative input. 57 i adc2lp adc2 left positive input. 58 i adc2ln adc2 le ft negative input. 59 i adc2rp adc2 right positive input. 60 i adc2rn adc2 right negative input. 61 o lf pll loop filter, return to avdd. 62 i avdd analog power supply. connect to analog 3.3 v supply. 63 nc no connect. 64 nc no connect.
ad1939 rev. c | page 11 of 32 typical performance character istics 0.10 0.08 0.06 0.04 0.02 0 ?0.10 ?0.08 ?0.06 ?0.04 ?0.02 0 1816141210 8642 magnitude (db) frequency (khz) 06071-002 figure 3 . adc pass- band filter response, 48 khz 0 ?10 ?20 ?30 ?40 ?50 ?60 ?70 ?80 ?90 ?100 0 40 5 10 15 20 25 30 35 magnitude (db) frequency (khz) 06071-003 figure 4 . adc stop- band filter response, 48 khz 0.06 0.04 0.02 ?0.06 ?0.04 ?0.02 0 0 24 16 8 magnitude (db) frequency (khz) 06071-004 figure 5 . dac pass- band filter response, 4 8 khz 0 ?150 ?100 ?50 0 48 12 24 36 magnitude (db) frequency (khz) 06071-005 figure 6 . dac stop- band filter response, 48 khz 0.10 ?0.10 ?0.05 0 0.05 0 96 72 48 24 magnitude (db) frequency (khz) 06071-006 figure 7 . dac pass- band filter response, 96 khz 0 ?150 ?100 ?50 0 96 24 48 72 magnitude (db) frequency (khz) 06071-007 figure 8 . dac stop- band filter response, 96 khz
ad1939 rev. c | page 12 of 32 0.5 ?0.5 ?0.4 ?0.3 ?0.2 ?0.1 0 0.1 0.2 0.3 0.4 0 64 8 16 32 magnitude (db) frequency (khz) 06071-008 figure 9 . dac pass- band filter response, 192 khz ?10 ?8 ?6 ?4 ?2 0 48 96 64 80 magnitude (db) frequency (khz) 06071-009 figure 10 . dac stop - band filter response, 192 khz
ad1939 rev. c | page 13 of 32 theory of operation analog - to - digital converters ( adcs) there are four analog - to - digital converter (adc) chan nels in the ad1939 configured as two stereo pairs with differential inputs. the adcs can operate at a nominal sample rate of 48 khz, 96 khz, or 192 khz. the adcs include on - board digital anti - aliasing filters with 79 db stop - band attenuation and linear pha se response, operating at an oversampling ratio of 128 (48 khz, 96 khz, and 192 khz modes). digital outputs are supplied through two serial data output pins (one for each stereo pair) and a common frame clock (alrclk) and bit clock (abclk). alternatively, one of the tdm modes can be used to access up to 16 channels on a single tdm data line. the adcs must be driven from a differential signal source for best performance. the input pins of the adcs connect to internal switched capacitors. to isolate the exter nal driving op amp from the glitches caused by the internal switched capacitors, each in - put pin should be isolated by using a series - connected external 100 resistor together with a 1 nf capacitor connected from each input to ground. this capacitor must be of high quality, for example, ceramic np0 or polypropylene film. the differential inputs have a nominal common - mode voltage of 1.5 v. the voltage at the common - mode reference pin (cm) can be used to bias external op amps to buffer the input signals (see the power supply and voltage reference section). the inputs can also be ac - coupled and do not need an external dc bias to cm. a d igital high - pass filter can be switched in line with the adcs under serial control to remove residual dc offsets. it has a 1.4 hz, 6 db per octave cutoff at a 48 khz sample rate. the cutoff fre - quency scales directly with sample frequency. digital - to - analo g converters (dacs) the ad1939 digital - to - analog converter (dac) channels are arranged as differential, four stereo pairs giving eight analog outputs for improved noise and distortion performance. the dacs include on - board digital reconstruction filters wi th 70 db stop - band attenuation and linear phase response, operating at an oversampling ratio of 4 (48 khz or 96 khz modes) or 2 (192 khz mode). each channel has its own independently programmable attenuator, adjustable in 255 steps in increments of 0.375 d b. digital inputs are supplied through four serial data input pins (one for each stereo pair) and a common frame clock (dlrclk) and bit clock (dbclk). alternatively, one of the tdm modes can be used to access up to 16 channels on a si ngle tdm data line. ea ch output pin has a nominal common - mode dc level of 1.5 v and swings 1.27 v for a 0 dbfs digital input signal. a single op amp, third - order, external, low - pass filter is recommended to remove high frequency noise present on the output pins, as well as to provide differential - to -single- ended conversion in the case of the differential output. note that the use of op amps with low slew rate or low bandwidth can cause high frequency noise and tones to fold down into the audio band; exercise care in selecting t hese components. the voltage at cm, the common - mode reference pin, can be used to bias the external op amps that buffer the output signals (see the power supply and voltage reference section). clock signals the on - chip phase - lock ed loop (pll) can be selected to reference the input sample rate from either of the lrclk pins or 256, 384, 512, or 768 times the sample rate, referenced to the 48 khz mode from the mclki/xi pin. the default at power - up is 256 f s from the mclki /xi pin . i n 96 khz mode, the master clock fre quency stays at the same absolute frequency; therefore, the actual multiplication rate is divided by 2. in 192 khz mode, the actual multiplication rate is divided by 4. for example, if a device in the ad1939 family is pr ogrammed in 256 f s mode, the frequency of the master clock input is 256 48 khz = 12.288 mhz. if the ad1939 is then switched to 96 khz o peration (by writing to the spi port), the frequency of the master clock should remain at 12.288 mhz, which is 128 f s in this example. in 192 khz mode, this becomes 64 f s . the internal clock for the adcs is 256 f s for all clock modes. the internal clock for the dacs varies by mode: 512 f s (48 khz mode), 256 f s (96 khz mode), or 128 f s (192 khz mode). by defau lt, the on - board pll generates this internal master clock from an external clock. a direct 512 f s (referenced to 48 khz mode) master clock can be used for either the adcs or dacs if selected in the pll and clock control 1 register. note that it is not po ssible to use a direct clock for the adcs set to the 192 khz mode. it is required that the on - chip pll be used in this mode. the pll can be powered down in the pll and clock control 0 register. to ensure reliable locking when changing pll modes, or if the reference clock is unstable at power - on, power down the pll and then power it back up when the reference clock stabilize s. the internal master clock (mclk) can be disabled in the pll and clock control 0 register to reduce power dissipation when the ad1939 is idle. the clock should be stable before it is enabled. unless a standalone mode is selected (see the serial control port section), the clock is disabled by reset and must be enabled by writing to the spi port for normal operati on. to maintain the highest performance possible, limit the clock jitter of the internal master clock signal to less than a 300 ps rms time interval error (tie ). even at these levels, extra noise or tones can appear in the dac outputs if the jitter spectru m contains large spectral peaks. if the internal pll is not used, it is best to use an independent crystal oscillator to generate the
ad1939 rev. c | page 14 of 32 master clock. in addition, it is especially important that the clock signal not pass through an fpga, cpld, or other large digital chip (such as a dsp) before being applied to the ad1939. in most cases, this induces clock jitter due to the sharing of common power and ground connections with other unrelated digital output signals. when the pll is used, jitter in the reference clock is attenuated above a certain frequency depending on the loop filter. reset and power - down the function of the rst pin sets all the control registers to their default settings. to avoid pops, reset does not power down the analog out puts. after rst is deasserted and the pll acquires lock condition, an initialization routine runs inside the ad1939. this initialization lasts for approximately 256 master clock cycles . the power - down bits in the pll and clock control 0, dac control 1, and adc control 1 registers power down the respective sections. all other register settings are retained. t o guarantee proper startup, t he rst pin should be pulled low by an external resistor. serial control port the ad1939 has an spi control port that permits programming and reading back of the internal control registers for the adcs, dacs, and clock system. a standalone mode is also available for operation without serial control; it is configured at reset using the serial control pins. all registers are set to default, except the internal mclk enable is set to 1 and adc bclk and lrclk master/slave is set by the cout pin. standalone mode only supports stereo mode with an i 2 s data format and 256 f s mclk rate. refer to table 11 for details. it is recommended to use a weak pull - up resistor on clatch in applications that have a microcontroller. this pull - up resistor ensures that the ad1939 recognizes the presence of a microcontroller. t he spi control port of the ad1939 is a 4 - wire serial control port. the format is similar to the motorola spi format except the input data - word is 24 bits wide. the serial bit clock and latch can be completely asynchronous to the sample rate of the adcs and dacs. figure 11 shows the format of the spi signal. the first byte is a global address with a read/write bit. for the ad1939 , the address is 0x04, shifted left one bit due to the r/ w bit. the second byte is the ad1939 register address and the third byte is the data. table 11 . standa lone mode selection adc clocks cin cout cclk clatch slave 0 0 0 0 master 0 1 0 0 d0 d0 d8 d8 d22 d23 d9 d9 clatch cclk cin cout t cch t ccl t cds t cdh t cls t ccp t clh t cots t cod t coe 06071-010 figure 11 . format of the spi signal
ad1939 rev. c | page 15 of 32 power supply and vol tage reference the ad1939 is designed for 3.3 v supplies. separate power supply pins are provided for the analog and digital sections. to minimize noise pickup, these pins should be bypassed with 100 nf ceramic chip capacitor s placed as close to the pins as possible. a bulk aluminum electrolytic capacitor of at least 22 f should also be provided on the same pc board as the codec. for critical applications, improved performance is obtained with separate supplies for the analog and digital sections. if this is not possible, it is recommended that the analog and digital sup plies be isolated by means of a ferrite bead in series with each supply. it is important that the analog supply be as clean as possible. the ad1939 includes a 3.3 v regulator driver that only requires an external pass transistor and bypass capacitors to ma ke a 5 v to 3.3 v regulator. if the regulator driver is not used, connect vsupply, vdrive, and vsense to dgnd. all digital inputs are compatible with ttl and cmos levels. all outputs are driven from the 3.3 v dvdd supply and are compatible with ttl and 3.3 v cmos levels. the adc and dac internal voltage reference (v ref ) is brought out on filtr and should be bypassed as close as possible to the chip with a parallel combination of 10 f and 100 nf. any external current drawn should be limited to less than 50 a. the internal reference can be disabled in the pll and clock control 1 register and filtr can be driven from an external source. this can be used to scale the dac output to the clipping level of a power amplifier based on its power supply voltage. the adc input gain varies by the inverse ratio. the total gain from adc input to dac output remains constant. the cm pin is the internal common - mode reference. it should be bypassed as close as possible to the chip, with a parallel combination of 47 f and 100 nf. this voltage can be used to bias external op amps to the common - mode voltage of the input and output signal pins. the output current should be limited to less than 0.5 ma source and 2 ma sink. serial data ports data format the eight dac channels use a common s erial bit clock (dbclk) and a common left - right framing clock (dlrclk) in the serial data port. the four adc channels use a common serial bit clock (abclk) and left - right framing clock (alrclk) in the serial data port. the clock signals are all syn chronous with the sample rate. the normal stereo serial modes are shown in figure 23. the adc and dac serial data modes default to i 2 s. the ports can also be programmed for left - justified, right - justified, and tdm modes. the word width is 24 bits by default and can be programmed for 16 or 20 bits. the dac serial formats are programmable according to the dac control 0 register. the polarity of dbclk and dlrclk is programmable according to the dac control 1 register. the adc serial f ormats and serial clock polarity are programmable according to the adc control 1 register. both dac and adc serial ports are programmable to become the bus masters according to dac control 1 register and adc control 2 register. by default, both adc and dac serial ports are in the slave mode. time - division multiplexed (tdm) modes the ad1939 serial ports also have several different tdm serial data modes. the first and most commonly used con figurations are shown in figure 12 and figure 13 . in figure 12 , the adc serial port outputs one data stream consisting of four on - chip adcs followed by four unused slots. in figure 13 , the eight on - chip dac data s lots are packed into one tdm stream. in this mode, both dbclk and abclk are 256 f s . slot 1 left 1 slot 2 right 1 slot 3 left 2 slot 4 right 2 msb msb?1 msb?2 data bclk lrclk slot 5 slot 6 slot 7 slot 8 lrclk bclk data 256 bclks 32 bclks 06071-016 figure 12 . adc tdm (8 - channel i 2 s mode) slot 1 left 1 slot 2 right 1 slot 3 left 2 slot 4 right 2 msb msb?1 msb?2 data bclk lrclk slot 5 left 3 slot 6 right 3 slot 7 left 4 slot 8 right 4 lrclk bclk data 256 bclks 32 bclks 06071-017 figure 13 . dac tdm (8 - channel i 2 s mode) the i/o pins of the serial ports are defined according to the serial mode that is selected. for a detailed description of the function of each pin in tdm and aux modes, see table 12 . the ad1939 allo ws systems with mor e than eight dac channels to be easily configured by the use of an auxiliary serial data port . the dac tdm - aux mode is shown in figure 14 . in this mode, the aux channels are the last four slots of the tdm data stream. these slots are extracted and output to the aux serial port. i t should be noted that due to the high dbclk frequency, this mode is available only in the 48 khz/44.1 khz/32 khz sample rate. the ad1939 also allows system configurations with more than four adc channels as shown in figure 15 (using 8 adcs) and figure 16 (using 16 adcs). again, due to the high abclk fre - quency, this mode is available only in the 48 khz/44.1 khz/32 khz sample rate.
ad1939 rev. c | page 16 of 32 combining the aux adc and dac modes results in a system configurat ion of 8 adcs and 12 dacs. the system, then, con - sists of two external stereo adcs, two external stereo dacs, and one ad1939. this mode is shown in figure 17 (combined aux dac and adc modes). table 12 . pi n function changes in tdm and aux modes pin mnemonic stereo modes tdm modes aux modes asdata1 adc1 data out adc tdm data out tdm data out asdata2 adc2 data out adc tdm data in aux data out 1 (to ext. dac 1) dsdata1 dac1 data in dac tdm data in tdm da ta in dsdata2 dac2 data in dac tdm data out aux data in 1 (from ext. adc 1) dsdata3 dac3 data in dac tdm data in 2 (dual - line mode) aux data in 2 (from ext. adc 2) dsdata4 dac4 data in dac tdm data out 2 (dual - line mode) aux data out 2 (to ext. dac 2 ) alrclk adc lrclk in/ adc lrclk out adc tdm frame sync in/ adc tdm frame sync out tdm frame sync in/ tdm frame sync out abclk adc bclk in/adc bclk out adc tdm bclk in/ adc tdm bclk out tdm bclk in/tdm bclk out dlrclk dac lrclk in/ dac lrclk out dac tdm fram e sync in/ dac tdm frame sync out aux lrclk in/ aux lrclk out dbclk dac bclk in/dac bclk out dac tdm bclk in/ dac tdm bclk out aux bclk in/ aux bclk out left right msb msb msb msb alrclk abclk dsdata1 (tdm_in) dl rcl k (aux port) dbclk (aux port) asdata2 (aux1_out) dsdata4 (aux2_out) msb empty empty empty empty dac l1 dac r1 dac l2 dac r2 dac l3 dac r3 dac l4 dac r4 aux l1 aux r1 aux l2 aux r2 8 on-chip dac channels auxiliary dac channels appear at aux dac ports unused slots 32 bits 06071-051 figure 14 . 16 - channel dac tdm - aux mode
ad1939 rev. c | page 17 of 32 alrclk abclk dsdata1 (tdm_in) asdata1 (tdm_out) dlrclk (aux port) dbclk (aux port) dsdata2 (aux1_in) dsdata3 (aux2_in) dac l1 dac r1 dac l2 dac r2 dac l3 dac r3 dac l4 dac r4 adc l1 adc r1 adc l2 adc r2 aux l1 aux r1 aux l2 aux r2 8 on-chip dac channels 4 on-chip adc channels 4 aux adc channels 32 bits left right msb msb msb msb msb 06071-050 figure 15 . 8- channel aux adc mode left right msb msb msb msb dlrclk (aux port) dbclk (aux port) dsdata2 (aux1_in) dsdata3 (aux2_in) alrclk abclk asdata1 (tdm_out) msb adc l1 adc r1 adc l2 adc r2 aux l1 aux r1 aux l2 aux r2 unused unused unused unused unused unused unused unused 4 on-chip adc channels auxiliary adc channels unused slots 32 bits 06071-052 figure 16 . 16 - channel aux adc mode
ad1939 rev. c | page 18 of 32 left right dlrclk (aux port) dbclk (aux port) msb msb dsdata2 (aux1_in) msb msb dsdata3 (aux2_in) msb msb asdata2 (aux1_out) msb msb dsdata4 (aux2_out) alrclk abclk dsdata1 (tdm_in) empty empty empty empty dac l1 dac r1 dac l2 dac r2 dac l3 dac r3 dac l4 dac r4 aux l1 aux r1 aux l2 aux r2 8 on-chip dac channels auxiliary dac channels appear at aux dac ports unused slots asdata1 (tdm_out) adc l1 adc r1 adc l2 adc r2 aux l1 aux r1 aux l2 aux r2 unused unused unused unused unused unused unused unused 4 on-chip adc channels auxiliary adc channels unused slots 06071-053 figure 17 . combined aux dac and adc mode
ad1939 rev. c | page 19 of 32 daisy - chain mode the ad1939 also allows a daisy - chain configuration to expand the system to 8 adcs a nd 16 dacs (see figure 18 ). in this mode, the dbclk frequency is 512 f s . the first eight slots of the dac tdm data stream belong to the first ad1939 in the chain and the last eight slots belong to the second ad1939. the second ad1 939 is the device attached to the dsp tdm port. to accommodate 16 channels at a 96 khz sample rate, the ad1939 can be configured into a dual - line, tdm mode as shown in figure 19 . this mode allows a slower dbclk than normally requi red by the one - line tdm mode. again, the first four channels of each tdm input belong to the first ad1939 in the chain and the last four channels belong to the second ad1939. the dual - line tdm mode can also be used to send data at a 192 khz sample rate int o the ad1939 as shown in figure 20 . there are two configurations for the adc port to work in daisy - chain mode. the first one is with an abclk at 256 f s shown in figure 21 . the second configuratio n is shown in figure 22 . note that in the 512 f s abclk mode, the adc channels occupy the first eight slots; the second eight slots are empty. the tdm_in of the first ad1939 must be grounded in all modes of operation. the i/o p ins of the serial ports are defined according to the serial mode selected. see table 13 for a detailed description of the function of each pin. see figure 26 for a typical ad1939 configuration wit h two external stereo dacs and two external stereo adcs. figure 23 through figure 25 show the serial mode formats. for maximum flexibility, the polarity of lrclk and bclk are programmable. in these figures, all of the clocks are shown with their normal polarity. the default mode is i 2 s. dlrclk dbclk 8 dac channels of the first ic in the chain 8 unused slots 8 dac channels of the second ic in the chain msb dsdata1 (tdm_in) of the second ad1939 dsdata2 (tdm_out) of the second ad1939 this is the tdm to the first ad1939 dac l1 dac r1 dac l2 dac r2 dac l3 dac r3 dac l4 dac r4 dac l1 dac r1 dac l2 dac r2 dac l3 dac r3 dac l4 dac r4 dac l1 dac r1 dac l2 dac r2 dac l3 dac r3 dac l4 dac r4 32 bits dsp second ad1939 first ad1939 06071-054 figure 18 . single - line dac tdm daisy - chain mode (applicable to 48 khz sample rate, 16 - channel, two - ad1939 daisy chain)
ad1939 rev. c | page 20 of 32 06071-055 dlrclk dbclk 8 dac channels of the second ic in the chain 8 dac channels of the first ic in the chain dsdata1 (in) dac l1 dac r1 dac l2 dac r2 dac l1 dac r1 dac l2 dac r2 dsdata3 (in) dac l3 dac r3 dac l4 dac r4 dac l3 dac r3 dac l4 dac r4 dsdata2 (out) dac l1 dac r1 dac l2 dac r2 dsdata4 (out) dac l3 dac r3 dac l4 dac r4 32 bits dsp second ad1939 first ad1939 msb figure 19 . dual - line dac tdm mode (applicable to 96 khz sample rate, 16 - channel, two - ad1939 daisy chain); dsdata3 and dsdata4 are the daisy chain dlrclk dbclk dsdata1 dac l1 dac r1 dac l2 dac r2 dsdata2 dac l3 dac r3 dac l4 dac r4 32 bits msb 06071-058 figure 20 . dual - line dac tdm mode (applicable to 192 khz sample rate, 8 - channel mode) alrclk abclk asdata2 (tdm_in of the second ad1939 in the chain) adc l1 adc r1 adc l2 adc r2 4 adc channels of first ic in the chain 4 adc channels of second ic in the chain asdata1 (tdm_out of the second ad1939 in the chain) adc l1 adc r1 adc l2 adc r2 adc l1 adc r1 adc l2 adc r2 32 bits msb dsp second ad1939 first ad1939 06071-056 figure 21 . adc tdm daisy - chain mode (256 f s abclk, two - ad1939 daisy chain)
ad1939 rev. c | page 21 of 32 alrclk abclk 4 adc channels of second ic in the chain 4 adc channels of first ic in the chain adc l1 adc r1 adc l2 adc r2 adc l1 adc r1 adc l2 adc r2 asdata1 (tdm_out of the second ad1939 in the chain) adc l1 adc r1 adc l2 adc r2 asdata2 (tdm_in of the second ad1939 in the chain) 32 bits msb dsp second ad1939 first ad1939 06071-057 figure 22 . adc tdm daisy - chain mode (512 f s abclk, two - ad1939 daisy chain) lrclk bclk sdata lrclk bclk sdata lrclk bclk sdata lsb lsb lsb lsb lsb lsb left channel right channel right channel left channel left channel right channel msb msb msb msb msb msb right-justified mode?select number of bits per channel dsp mode?16 bits to 24 bits per channel i 2 s-justified mode?16 bits to 24 bits per channel left-justified mode?16 bits to 24 bits per channel lrclk bclk sdata lsb lsb notes 1. dsp mode does not identify channel. 2. lrclk normally operates at f s except for dsp mode, which is 2 f s . 3. bclk frequency is normally 64 lrclk but may be operated in burst mode. msb msb 1/ f s 06071-013 figure 23 . stereo serial modes
ad1939 rev. c | page 22 of 32 dbclk dlrclk dsdatax left-justified mode dsdatax right-justified mode dsdatax i 2 s-justified mode t dlh t dbh t dbl t dls t dds msb msb msb lsb msb?1 t ddh t dds t ddh t dds t ddh t ddh t dds 06071-014 figure 24 . dac serial timing abclk alrclk asdatax left-justified mode asdatax right-justified mode asdatax i 2 s-justified mode t abh lsb msb msb msb msb?1 t abl t als t abdd t abdd t abdd t alh 06071-015 figure 25 . adc serial timing
ad1939 rev. c | page 23 of 32 table 13 . pin function changes in tdm and aux modes (replication of t able 12 ) pin mnemonic stereo modes tdm modes aux modes asdata1 adc1 data out adc tdm data out tdm data out asdata2 adc2 data out adc tdm data in aux data out 1 (to ext. dac 1) dsdata1 dac1 data in dac tdm data in tdm data in dsdata2 dac2 data in d ac tdm data out aux data in 1 (from ext. adc 1) dsdata3 dac3 data in dac tdm data in 2 (dual - line mode) aux data in 2 (from ext. adc 2) dsdata4 dac4 data in dac tdm data out 2 (dual - line mode) aux data out 2 (to ext. dac 2) alrclk adc lrclk in/adc lrc lk out adc tdm frame sync in/ adc tdm frame sync out tdm frame sync in/ tdm frame sync out abclk adc bclk in/adc bclk out adc tdm bclk in/adc tdm bclk out tdm bclk in/tdm bclk out dlrclk dac lrclk in/dac lrclk out dac tdm frame sync in/ dac tdm frame sync o ut aux lrclk in/aux lrclk out dbclk dac bclk in/dac bclk out dac tdm bclk in/dac tdm bclk out aux bclk in/aux bclk out aux adc 1 lrclk bclk data mclk aux adc 2 lrclk bclk data mclk aux dac 1 aux dac 2 lrclk bclk data mclk lrclk bclk data mclk 30mhz 12.288mhz sharc is running in slave mode (interrupt-driven) sharc ? ad1939 tdm master aux master fsync-tdm (rfs) rxclk rxdata txclk txdata tfs (nc) asdata2 dsdata4 dbclk dlrclk dsdata2 dsdata3 mclki/xi asdata1 alrclk abclk dsdata1 06071-019 figure 26 . example of aux mode connection to sharc (ad1939 as tdm master/aux master shown)
ad1939 rev. c | page 24 of 32 control registe rs definitions the global address for the ad1939 is 0x04, shifted left one bit due to the r/ w bit. all registers are reset to 0, except for the dac volume registers that are set to full volume. note that the first setting in each contro l register parameter is the default setting. table 14 . register format global address r/ w register address data bit 23:17 16 15:8 7:0 table 15 . register addresses and functions address fu nction 0 pll and clock control 0 1 pll and clock control 1 2 dac control 0 3 dac control 1 4 dac control 2 5 dac individual channel mutes 6 dac l1 volume control 7 dac r1 volume control 8 dac l2 volume control 9 dac r2 volume control 10 dac l3 v olume control 11 dac r3 volume control 12 dac l4 volume control 13 dac r4 volume control 14 adc control 0 15 adc control 1 16 adc control 2 pll and clock contro l registers table 16 . pll and clock control 0 register bit value function description 0 0 normal operation pll power - down 1 power - down 2:1 00 input 256 ( 44.1 khz or 48 khz) mclki/xi pin functionality (pll active), master clock rate setting 01 input 384 ( 44.1 khz or 48 khz) 10 input 512 ( 44.1 khz or 48 k hz) 11 input 768 ( 44.1 khz or 48 khz) 4:3 00 xtal oscillator enabled mclko/xo pin , master clock rate setting 01 256 f s vco output 10 512 f s vco output 11 off 6:5 00 mclki /xi pll input 01 dlrclk 10 alrclk 11 reserved 7 0 dis able: adc and dac idle internal master clock enable 1 enable: adc and dac active
ad1939 rev. c | page 25 of 32 table 17 . pll and clock control 1 register bit value function description 0 0 pll clock dac clock source select 1 mclk 1 0 pll clock adc cl ock source select 1 mclk 2 0 enabled on - chip voltage reference 1 disabled 3 0 not locked pll lock indicator (read only) 1 locked 7:4 0000 reserved dac control register s table 18 . dac control 0 register bit value func tion description 0 0 normal power - down 1 power - down 2:1 00 32 khz/44.1 khz/48 khz sample rate 01 64 khz/88.2 khz/96 khz 10 128 khz/176.4 khz/192 khz 11 reserved 5:3 000 1 sdata delay (bclk periods) 001 0 010 8 011 12 100 16 10 1 reserved 110 reserved 111 reserved 7:6 00 stereo (normal) serial format 01 tdm (daisy chain) 10 dac aux mode (adc - , dac - , tdm - coupled) 11 dual - line tdm table 19 . dac control 1 register bit value function descrip tion 0 0 latch in mid cycle (normal) bclk active edge (tdm in) 1 latch in at end of cycle (pipeline) 2:1 00 64 (2 channels) bclks per frame 01 128 (4 channels) 10 256 (8 channels) 11 512 (16 channels) 3 0 left low lrclk polarity 1 left hig h 4 0 slave lrclk master/slave 1 master 5 0 slave bclk master/slave 1 master 6 0 dbclk pin bclk source 1 internally generated 7 0 normal bclk polarity 1 inverted
ad1939 rev. c | page 26 of 32 table 20 . dac control 2 register bit value function description 0 0 unmute master m ute 1 mute 2:1 00 flat de - emphasis (32 khz/44.1 khz/48 khz mode only) 01 48 khz curve 10 44.1 khz curve 11 32 khz curve 4:3 00 24 word width 01 20 10 reserved 11 16 5 0 noninverted dac output polarity 1 inverted 7:6 00 reserved table 21 . dac individual channel mutes bit value function description 0 0 unmute dac 1 left mute 1 mute 1 0 unmute dac 1 right mute 1 mute 2 0 unmute dac 2 left mute 1 mute 3 0 unmute d ac 2 right mute 1 mute 4 0 unmute dac 3 left mute 1 mute 5 0 unmute dac 3 right mute 1 mute 6 0 unmute dac 4 left mute 1 mute 7 0 unmute dac 4 right mute 1 mute table 22 . dac volume controls bit value function de scription 7:0 0 no attenuation dac volume control 1 to 254 ?3/8 db per step 255 full attenuation
ad1939 rev. c | page 27 of 32 adc control register s table 23 . adc control 0 register bit value function description 0 0 normal power - down 1 power down 1 0 off high - pass filter 1 on 2 0 unmute adc 1l mute 1 mute 3 0 unmute adc 1r mute 1 mute 4 0 unmute adc 2l mute 1 mute 5 0 unmute adc 2r mute 1 mute 7:6 00 32 khz/44.1 khz/48 khz output sample rate 01 64 khz/88.2 khz/96 khz 10 128 khz/176.4 khz/192 khz 11 reserved table 24 . adc control 1 register bit value function description 1:0 00 24 word width 01 20 10 reserved 11 16 4:2 000 1 sdata delay (bclk periods) 001 0 010 8 011 12 100 16 101 reserved 110 reserved 111 reserved 6:5 00 stereo serial format 01 tdm (daisy chain) 10 adc aux mode (adc - , dac - , tdm - coupled) 11 reserved 7 0 latch in mid cycle (normal) bclk active edge (tdm in) 1 latch in at end of cycle (pip eline)
ad1939 rev. c | page 28 of 32 table 25 . adc control 2 register bit value function description 0 0 50/50 (allows 32 , 24 , 20 , or 16 bit clocks ( bclk s) per channel) lrclk format 1 pulse (32 bclk s per channel) 1 0 drive out on falling edge (def) bcl k polarity 1 drive out on rising edge 2 0 left low lrclk polarity 1 left high 3 0 slave lrclk master/slave 1 master 5:4 00 64 bclks per frame 01 128 10 256 11 512 6 0 slave bclk master/slave 1 master 7 0 abclk pin bclk source 1 internally generated
ad1939 rev. c | page 29 of 32 additional modes the ad1939 offers several additional modes for board level design enhancements. to reduce the emi in board level design, serial data can be transmitted without an explicit bclk. see figur e 27 for an example of a dac tdm data transmission mode that does not require high speed dbclk. this configura - tion is applicable when the ad1939 master clock is generated by the pll with the dlrclk as the pll reference frequency. to relax the requiremen t for the setup time of the ad1939 in cases of high speed tdm data transmission, the ad1939 can latch in the data using the falling edge of dbclk. this effec - tively dedicates the entire bclk period to the setup time. this mode is useful in cases where the source has a large delay time in the serial data driver. figure 28 shows this pipeline mode of data transmission. both the b cl k- less and pipeline modes are available on the adc serial data port. dlrclk internal dbclk dsdatax dlrclk internal dbclk tdm-dsdatax 32 bits 06071-059 figure 27 . serial dac data transmission in tdm format without dbclk (applicable only if pll loc ks to dlrclk, this mode is also available in the adc serial data port) dlrclk dbclk dsdatax data must be valid at this bclk edge msb 06071-060 figure 28 . i 2 s pipeline mode in dac serial data transmission (applica ble in stereo and tdm, useful for high frequency tdm transmission, this mode is also available in the adc serial data port)
ad1939 rev. c | page 30 of 32 application circuits typical application circuits are shown in figure 29 through figure 32. figure 29 shows a typical adc input filter circuit. recommended loop filters for lr clock and master clock as the pll reference are shown in figure 30 . output filters for the dac outputs are shown in figure 31 and a regulator circuit is shown in figure 32 . 2 1 3 op275 ? + 6 7 5 op275 ? + 5.76k ? 5.76k ? 237? 5.76k ? 120pf 600z audio input 100pf 5.76k ? 120pf 4.7f + 237? 4.7f + 100pf 1nf npo 1nf npo adcxn adcxp 06071-029 figure 29 . typical adc input filter circuit 39nf + 2.2nf lf lrclk avdd2 3.32k ? 5.6nf 390pf lf mclk avdd2 562? 06071-030 figure 30 . recommended loop filters for lrclk or mclk pll reference 06071-031 2 1 3 op275 ? + 2.2nf npo audio output 604? 68pf npo 560pf npo 270pf npo dac outn 3.01k ? 11k? dac outp 1.50k ? 5.62k ? 11k? 5.62k ? figure 31 . typical dac output filter circuit (differential) 10f + e c b vsupply 5v vsense 3.3v fzt953 vdrive 1k? 100nf 10f + 100nf 06071-032 figure 32 . recommended 3.3 v regulator circuit
ad1939 rev. c | page 31 of 32 outline dimensions compliant t o jedec s t andards ms-026-bcd 051706- a top view (pins down) 1 16 17 33 32 48 49 64 0.27 0.22 0.17 0.50 bsc lead pitch 12.20 12.00 sq 1 1.80 pin 1 1.60 max 0.75 0.60 0.45 10.20 10.00 sq 9.80 view a 0.20 0.09 1.45 1.40 1.35 0.08 coplanarit y view a ro ta ted 90 ccw se a ting plane 0.15 0.05 7 3.5 0 figure 33 . 64 - lead low profile quad flat package [lqfp] (st - 64 - 2) dimensions shown in millimeters ordering guide model 1 , 2 temperature range package description package option ad1939ystz C 40c to +105c 64- lead lqfp st- 64 -2 AD1939YSTZRL C 40c to +105c 64- lead lqfp, 13 tape and reel st- 64 -2 ad1939w bstz C 40c to +105c 64- lead lqfp st- 64 -2 ad1939w bstz- rl C 40c to +105c 64- lead lqfp, 13 tape and reel st- 64 -2 eval - ad1939az evaluation board 1 z = rohs compliant part. 2 w = qualified for automotive applicatio ns. automotive products the ad1939 w models are available with co ntrolled manufacturing to support the quality and reliability requirements of automotive applications. note that these automotive models may have specifications that differ from the commercial models; therefore, de signers should review the specifications section of this data sheet carefully. only the automotive grade products shown are available for use in automotive applications. contact your local analog devices account representative for specific product ordering information and to obtain the specific automotive reliability reports for these models.
ad1939 rev. c | page 32 of 32 notes ? 2006 C 2010 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d06071 -0- 9/10(c)

▲Up To Search▲

Price & Availability of AD1939YSTZRL

	To Download AD1939YSTZRL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .